<!-- vim: ft=xml:
-->
<lexicon lang="en-us">
    <entry>
        <base>FORM_TITLE</base>
        <trans>Configure Port Forwarding</trans>
    </entry>
    <entry>
        <base>FIRST_PAGE_DESCRIPTION</base>
        <trans><![CDATA[
            <p>
                You can use this panel to modify your firewall rules so
                as to open a specific port on this server and forward it
                to another port on another host.  Doing so will permit
                incoming traffic to directly access a private host on
                your LAN.
            </p>
            <p>
                WARNING: Misuse of this feature can seriously compromise the
                security of your network. Do not use this feature
                lightly, or without fully understanding the implications
                of your actions.
            </p>
            ]]>
        </trans>
    </entry>
    <entry>
        <base>CREATE_RULE</base>
        <trans>Create portforwarding rule</trans>
    </entry>
    <entry>
        <base>SUMMARY_ADD_DESC</base>
        <trans>The following summarizes the port-forwarding rule
            that you are about to add. If you are satisfied with the rule,
            click the &quot;Add&quot; button. If you are not, click the
            &quot;Cancel&quot; button.
        </trans>
    </entry>
    <entry>
        <base>SUMMARY_REMOVE_DESC</base>
        <trans>The following summarizes the port-forwarding rule
            that you are about to remove. If you are sure you want to 
            remove the rule, click the &quot;Remove&quot; button. If not,
            click the &quot;Cancel&quot; button.
        </trans>
    </entry>
    <entry>
        <base>SHOW_FORWARDS</base>
        <trans>
    Below you will find a table summarizing the current
            port-forwarding rules installed on this server. Click on the
            &quot;Remove&quot; link to remove the corresponding rule.
    </trans>
    </entry>
    <entry>
        <base>NO_FORWARDS</base>
        <trans>There are currently no forwarded ports on the system.</trans>
    </entry>
    <entry>
        <base>CREATE_PAGE_DESCRIPTION</base>
        <trans><![CDATA[
            <p>Select the protocol, the port you wish to forward, the
                destination host, and the port on the destination host
                that you wish to forward to. If you wish to specify a port
                range, enter the lower and upper boundaries separated by a
                hyphen. The destination port may be left blank, which will
                instruct the firewall to leave the source port 
                unaltered.</p>
            ]]>
        </trans>
    </entry>
    <entry>
        <base>LABEL_SOURCE_PORT</base>
        <trans>Source Port(s)</trans>
    </entry>
    <entry>
        <base>LABEL_PROTOCOL</base>
        <trans>Protocol</trans>
    </entry>
    <entry>
        <base>LABEL_DESTINATION_PORT</base>
        <trans>Destination Port(s)</trans>
    </entry>
    <entry>
        <base>LABEL_DESTINATION_HOST</base>
        <trans>Destination Host IP Address</trans>
    </entry>
    <entry>
        <base>Configuration</base>
        <trans>Configuration</trans>
    </entry>
    <entry>
        <base>Port forwarding</base>
        <trans>Port forwarding</trans>
    </entry>
    <entry>
        <base>Security</base>
        <trans>Security</trans>
    </entry>
    <entry>
        <base>SAVE</base>
        <trans>Save</trans>
    </entry>
    <entry>
        <base>APPLY</base>
        <trans>Add</trans>
    </entry>
    <entry>
        <base>NEXT</base>
        <trans>Next</trans>
    </entry>
    <entry>
        <base>CANCEL</base>
        <trans>Cancel</trans>
    </entry>
    <entry>
        <base>SUCCESS</base>
        <trans>Your change to the port forwarding rules has been
        successfully saved.
        </trans>
    </entry>
    <entry>
        <base>REMOVE</base>
        <trans>Remove</trans>
    </entry>
    <entry>
        <base>SOURCE_PORT</base>
        <trans>Source Port(s)</trans>
    </entry>
    <entry>
        <base>DESTINATION_HOST</base>
        <trans>Destination Host IP Address</trans>
    </entry>
    <entry>
        <base>DESTINATION_PORT</base>
        <trans>Destination Port(s)</trans>
    </entry>
    <entry>
        <base>PROTOCOL</base>
        <trans>Protocol</trans>
    </entry>
    <entry>
        <base>ERR_NO_MASQ_RECORD</base>
        <trans>Cannot retrieve masq record from the configuration
        database.</trans>
    </entry>
    <entry>
        <base>ERR_UNSUPPORTED_MODE</base>
        <trans>Unsupported mode.</trans>
    </entry>
    <entry>
        <base>ERR_CANNOT_REMOVE_NORULE</base>
        <trans>Cannot remove non-existant rule.</trans>
    </entry>
    <entry>
        <base>ERR_NONZERO_RETURN_EVENT</base>
        <trans>Event returned a non-zero return value.</trans>
    </entry>
    <entry>
        <base>ERR_BADPORT</base>
        <trans>The ports must be a positive integer less than 
        65536.</trans>
    </entry>
    <entry>
        <base>ERR_BADIP</base>
        <trans>This does not appear to be an IP address. You must use
        dotted-quad notation, and each of the four numbers should be less
        than 256. ie: 192.168.0.5</trans>
    </entry>
    <entry>
        <base>ERR_DUPRULE</base>
        <trans>This rule has already been added, it cannot be added
        twice.</trans>
    </entry>
    <entry>
        <base>ACTION</base>
        <trans>Action</trans>
    </entry>
    <entry>
        <base>ERR_PORT_COLLISION</base>
        <trans>
            ERROR: This port or port range conflicts with an existing
            rule. Please modify this new rule, or remove the old rule.
        </trans>
    </entry>
    <entry>
        <base>IN_SERVERONLY</base>
        <trans>
            This server is currently in serveronly mode and portforwarding
	    is not possible.
        </trans>
    </entry>
</lexicon>
